Thursday 23 October 2003 3:32:14 pm

Actually I have the same problem. I installed the script using default settings, but after installation it just gives me 404 error, document not found. Documentation stated that the url to Admin-panel would be something like "www.mydomain.com/index.php/plain_admin". This puzzles me, because there isn't anything under this kind of URL. What have I done wrong?

Tuesday 04 November 2003 1:41:04 am

Well, this is certainly disheartening. I am experiencing the same problem with 3.2-3, and no solution is in sight? I am running Red Hat 9, standard install. I installed php-mysql rpm when setup complained about lack of mysql support, then everything was successful. I made sure all files are owned by user apache, which is what httpd runs under. The mysql db is getting populated, as well. I tried four different installs, until I was changing only the bare minimum from the defaults, and still nothing.

I have the same problem where the links given to me after setup finishes are "not found." I found out that if I go to sitename.com/installdir/index.php, I do get a working "Root folder" page, but all the links from this page are dead, too. Anyone having any luck yet?

Thanks in advance.

Tuesday 04 November 2003 11:49:04 am

Thanks for your quick response!

Yes, settings/override/site.ini.append.php was created. I even modified it to set CheckValidity=true so I could easily reinstall it.

The site is publicly accessible:

http://crackteam.org/hq/index.php

That's the one page you can see, and verify the links don't work. The two standard links that setup gives you for plain and plain_admin did not work at all.

Thanks again...

Wednesday 05 November 2003 5:01:06 am

Hi Philip

It looks like you need to alter your apache settings a bit. Please check the link below for description. Remember to move the .htaccess_root to .htaccess.

http://ez.no/developer/ez_publish_3/documentation/configuration/troubleshooting/ez_publish_3_and_apache_2

Kåre Høvik

Wednesday 05 November 2003 9:25:21 am

I experienced very similar problems with another CMS I ran a trial on a couple of weeks ago, and found that there were two possible reasons for the 404 errors. Number one is that for some reason Apache 2 doesn't like commands being called in the way that they are (ie: http://www.ezpublish.com/index.php/variable/value) where the traditional method has always been http://www.ezpublish.com/index.php?variable=value. You will also experience many of the same problems if PHP is being run as CGI on your server. I hate to say this, but if either of these are the root cause of the problem, there's not much you can do in my experience other than hack every single output buffer in the source code!

Tuesday 13 April 2004 9:48:26 pm

i have download and installed ezpublish-3[2].3-4.zip.I installed it on my local machine. After installing ezpublish had showed two links i.e user site<b>(http://localhost/ezpublish/index.php/corporate)</b> and admin site <b>(http://localhost/ezpublish/index.php/corporate_admin)</b>. But When i clicked to these url it shows me <b>"page cannot be displayed"</b>.Did i missed something to install or should i have not make changes in some configure file.What should i do to make these links runnable.
I am using
1)<b>Apache 2.0</b> (installed on c:\apache\)
2)<b>Php4.3.5</b> (Installed on c:\php\)
3)<b>mysql 4.0.18</b> (Installed on c:\mysql\)

Thanks in advance
Ashok Naidu

Wednesday 14 April 2004 12:04:21 am

I added the following three lines in httpd.conf.
<Files ~ "\.php$">
AcceptPathInfo On
</Files>
But Still it is not working.Please specify the place where to put the above three line in httpd.conf.There are also the following entry in my httpd.conf file
<Files *.html>
SetHandler type-map
AcceptPathInfo On
</Files>

<Files ~ "^\.ht">
Order allow,deny
Deny from all
AcceptPathInfo On
</Files>
should i remove these entry .Please tell me the solution.

Thanks
Ashok Naidu